BAKFlip 448203 MX4 (GEN 3) Hard Folding Tonneau Cover Fits 02-24 Ram 1500, 03-26 2500/3500 6'4" Bed

Fairly easy install. The videos help a lot. I had a slight issue with the rails leaning down slightly after being tightened. This kept the latches from catching when unrolled. After re-installing several times to see if I'd done something wrong, I just used a pair channel locks and bent the rails ever so slightly where the latches would make contact. Just enough to get it to latch without actually being able to see it. Worked great from there out.

The cover is of high quality and fit the truck nicely. I had a Revolver roll-up cover on my previous truck and really liked it as well, but thought I would try a fold up on this truck. Fit and finish is nice. The only issue I have is my truck (and my previous truck as well) has Ram Boxes. While the cover fits good, there are gaps on both sides at the tailgate that lets in quite a bit of water. This was not the case with the Revolver cover (It let a small amount). I do wonder if there is a solution to this. Other than that the cover is awesome.

When I purchased my truck it had a Peragon Classic retractable cover. I grew tired of my equipment getting wet. While no coveris100% waterproof I was impressed after going through the car wash. Install . . only one glitch. . it wasn't clear that the front rail tab went in at slight angle and the snapped in. . No real issue with the install even as I did it alone. . great looks and great product. .

Cover is good overall. The instructions could be clearer on the clamping the rails down section. Overall it looks good. However I had a bumper peice fall off already. The one that sits flush on top of the cover by the cab window when not in use. Hopefully it lasts a long time.

I just installed my cover and it looks great. It was a very easy installation. The only part about the cover I dislike is once I put the cover on and looked around the whole thing the spots where it folds were a little torn up. Being brand new that shouldn't be like that.

Installation was much more difficult for the Maverick than what is indicated in the Realtruck video. For $1200 it would have been helpful for an instruction sheet specifically for this model to be included. The tolerances for the Bakflip are so precise that any small imperfections in the truck bed are problematic. The drivers side latched perfectly but the passenger side would not latch for all three latches. Yes, the railing was installed correctly and identically on both sides. Determined that the truck bed was slightly leaning in on the passenger side. Had to correct by placing a flat washer as a shim under each latching mechanism. Also, the thick pads included to protect the cab are not thick enough for the Maverick. When the bed cover is flipped up it rests on the cab and the pads do not reach the cab. The rear window is recessed from the cab frame and the pads do not reach the window. The only place where the pads would actually work are on the very edge of the cover, and then it would not be able to close.

The installation didn't go as well as I had expected. I followed the provided instructions and the latches on the panels didn't line up correctly and wouldn't latch without me lifting the rail up. Because of the fitmet issue, it took me approximately two hours to install. The following day, I did research on the internet and found a reddit post outlining this as others experienced the same issue. Someone posted a link to a good video that showed installation with the brackets being snapped onto the rail. I removed my cover and rails and did another install snapping the brackets into the rail. The brackets are supposed to connect on the top notch but my middle brackets won't connect on the top notch so I had to connect on the bottom notch. The panels now latch as they should. I noticed that I can see some daylight in the corners of the cover by the cab, so I'll jave to put on more weather stripping in those spots. For the price, I expected better instructions.

I tried to communicate this with Realtruck, but there was too much red tape to make it worthwhile. There is a MAJOR issue with the written instructions that come with the cover that I purchased. No where in the instructions does it say that the clamps that hold the rail onto the bed should snap into the rail. If you don't snap them into the rail then the whole thing does not work at all. It will not latch and close up. I had to search Youtube in order to find this.

I took it to a professional install place for BakFlip. They say the parts for 2025 pro 4X was not great . They had to adjust finally got it to shut. But they told me today to reach out to you and say it not a normal installation. ( I try to reach customer service but it was a 30 plus min wait. Today 6/4/25

This isn't a review of the cover because you never sent it to me. A week after I ordered the cover it still showed as Pending Fulfillment. I called customer service and they said they'd get back to me. A week later they still hadn't gotten back to me so I bought the same cover from another online retailer and got it the next day. I cancelled the order from Realtruck and it still shows as Pending cancellation. I called customer service and was told they'd take care of it. Two days later there's no change. I won't be buying anything from Realtruck in the future.