BAKFlip 448207 MX4 (GEN 3) Hard Folding Tonneau Cover Fits 09-24 Ram 1500 Classic 5'7" Bed w/o RamBoxes

I really tried my best with help to make the side rail square with bed sides. The foam strip seems to put the rail at an angle. I loosened/tighted the rails to no avail. The cover does leak but not excessively but it leaks. Any advice would be appreciated. S.

My husband is pleased with the truck bed cover. My only complaints is that communication was lacking. We were up against a time crunch and after a week we had not received a shipping notice and i reached out for an update and received a reply that our order was processing. We never received a shipping notice and the cover showed up last week.

This is my 3rd BakFlip install over the past 9 years! I like how easy they are to install. I also like the low, clean appearance of the cover yet how secure they are from casual thieves etc. This new iteration feels lighter and better hinged. I like it!! My only complaint if you can call it that is that the 3 block bumpers have always resisted my attempts to peal the paper from the double sided tape that reveals the sticky side so you can install the bumps to the last panel that rest on the truck rear window. I can never get those to work properly.

4 inch long rubber bumpers that the cover edge sits on while fully open, not affixed very well. They were low quality adhesive. Cleaned off and used 3M trim double sided tape to fix. Stuck well now. Was disappointed to to see latches were plastic. Overall, product will work.

Installation was much more difficult for the Maverick than what is indicated in the Realtruck video. For $1200 it would have been helpful for an instruction sheet specifically for this model to be included. The tolerances for the Bakflip are so precise that any small imperfections in the truck bed are problematic. The drivers side latched perfectly but the passenger side would not latch for all three latches. Yes, the railing was installed correctly and identically on both sides. Determined that the truck bed was slightly leaning in on the passenger side. Had to correct by placing a flat washer as a shim under each latching mechanism. Also, the thick pads included to protect the cab are not thick enough for the Maverick. When the bed cover is flipped up it rests on the cab and the pads do not reach the cab. The rear window is recessed from the cab frame and the pads do not reach the window. The only place where the pads would actually work are on the very edge of the cover, and then it would not be able to close.

The installation didn't go as well as I had expected. I followed the provided instructions and the latches on the panels didn't line up correctly and wouldn't latch without me lifting the rail up. Because of the fitmet issue, it took me approximately two hours to install. The following day, I did research on the internet and found a reddit post outlining this as others experienced the same issue. Someone posted a link to a good video that showed installation with the brackets being snapped onto the rail. I removed my cover and rails and did another install snapping the brackets into the rail. The brackets are supposed to connect on the top notch but my middle brackets won't connect on the top notch so I had to connect on the bottom notch. The panels now latch as they should. I noticed that I can see some daylight in the corners of the cover by the cab, so I'll jave to put on more weather stripping in those spots. For the price, I expected better instructions.

I tried to communicate this with Realtruck, but there was too much red tape to make it worthwhile. There is a MAJOR issue with the written instructions that come with the cover that I purchased. No where in the instructions does it say that the clamps that hold the rail onto the bed should snap into the rail. If you don't snap them into the rail then the whole thing does not work at all. It will not latch and close up. I had to search Youtube in order to find this.

This isn't a review of the cover because you never sent it to me. A week after I ordered the cover it still showed as Pending Fulfillment. I called customer service and they said they'd get back to me. A week later they still hadn't gotten back to me so I bought the same cover from another online retailer and got it the next day. I cancelled the order from Realtruck and it still shows as Pending cancellation. I called customer service and was told they'd take care of it. Two days later there's no change. I won't be buying anything from Realtruck in the future.

Well let's see. It's been over a month since I placed my order. When I placed my order, the product was supposedly in stock and ready to ship. Still nothing. I am going to cancel my order and get the same bed cover from someone else. But since you asked for a review, here it is.

I ordered my part almost a month ago. I have not received it. I tried numerous times to get an update with no success. I am heading out for an extended trip and I needed the topper. Now I have to consider not having the part I needed for my trip. To add insult to injury I am being asked how I like the part I never receive. Kind of silly. Not a great first experience of a company that is “apparently” highly regarded. I am not a person of high expectations I just would like to know if I will get my part in time to install it before my trip. They took my payment. Will they be just as eager to return it? We shall see in 2 days when I will demand a refund.