BAKFlip 448226 MX4 (GEN 3) Hard Folding Tonneau Cover Fits 19-26 Ram 1500 5'7" Bed w/o RB,w/MFTG

My only "problem" which it wasn't for my nephew was the pre-drilling of the hole in the plastic lip of the top body cover. A guide that would not require the clip be in place would have made this installation a bit easier for an old guy with kneeling issues like me. My nephew handled it with ease.

This is my 3rd BakFlip install over the past 9 years! I like how easy they are to install. I also like the low, clean appearance of the cover yet how secure they are from casual thieves etc. This new iteration feels lighter and better hinged. I like it!! My only complaint if you can call it that is that the 3 block bumpers have always resisted my attempts to peal the paper from the double sided tape that reveals the sticky side so you can install the bumps to the last panel that rest on the truck rear window. I can never get those to work properly.

I went from a ARE fiberglass lid to this. . . Which limits you extremely. . The MX4 cover looks really good. . . . Easy install. . locks with tailgate. . Was missing one screw for the buckle latch, no biggie. . . never throw out extra hardware from any install!! Overall happy with product

The cover is of high quality and fit the truck nicely. I had a Revolver roll-up cover on my previous truck and really liked it as well, but thought I would try a fold up on this truck. Fit and finish is nice. The only issue I have is my truck (and my previous truck as well) has Ram Boxes. While the cover fits good, there are gaps on both sides at the tailgate that lets in quite a bit of water. This was not the case with the Revolver cover (It let a small amount). I do wonder if there is a solution to this. Other than that the cover is awesome.

Fairly easy install. The videos help a lot. I had a slight issue with the rails leaning down slightly after being tightened. This kept the latches from catching when unrolled. After re-installing several times to see if I'd done something wrong, I just used a pair channel locks and bent the rails ever so slightly where the latches would make contact. Just enough to get it to latch without actually being able to see it. Worked great from there out.

I just installed my cover and it looks great. It was a very easy installation. The only part about the cover I dislike is once I put the cover on and looked around the whole thing the spots where it folds were a little torn up. Being brand new that shouldn't be like that.

Installation was much more difficult for the Maverick than what is indicated in the Realtruck video. For $1200 it would have been helpful for an instruction sheet specifically for this model to be included. The tolerances for the Bakflip are so precise that any small imperfections in the truck bed are problematic. The drivers side latched perfectly but the passenger side would not latch for all three latches. Yes, the railing was installed correctly and identically on both sides. Determined that the truck bed was slightly leaning in on the passenger side. Had to correct by placing a flat washer as a shim under each latching mechanism. Also, the thick pads included to protect the cab are not thick enough for the Maverick. When the bed cover is flipped up it rests on the cab and the pads do not reach the cab. The rear window is recessed from the cab frame and the pads do not reach the window. The only place where the pads would actually work are on the very edge of the cover, and then it would not be able to close.

Cover was missing installation components …needed to wait on that . One of the clips on the rail is broken it has been sitting in FedEx “shipping label created” for a week. Really slow to just get it fully functional . Ensuring the install kit is complete replacing things broken in shipment should not take so long Bak is really slow

I tried to communicate this with Realtruck, but there was too much red tape to make it worthwhile. There is a MAJOR issue with the written instructions that come with the cover that I purchased. No where in the instructions does it say that the clamps that hold the rail onto the bed should snap into the rail. If you don't snap them into the rail then the whole thing does not work at all. It will not latch and close up. I had to search Youtube in order to find this.

It was very Disappointing or may be my expectations were to high!!!. . . never got the cover to latch naturally and properly unless you help it or force it ( is not the way it supposed to work ) the clips that holds the bed cover tight with the railing interfere with the hardware ( ended up both line up in the same spot ) plastic clips on the end of over railing sistem comes loose pretty easy ( not supposed to be like that ) installation were rate as easy to install ( turned into a headache ) got me working on it over 3 times. In Resume. Overall quality i think was poor ( I could expect that from an unbranded product from Amazon or so ) not from the a top saller product