BAKFlip 448332 MX4 (GEN 3) Hard Folding Tonneau Cover Fits 2019-2023 Ford Ranger 5'1" Bed

I went from a ARE fiberglass lid to this. . . Which limits you extremely. . The MX4 cover looks really good. . . . Easy install. . locks with tailgate. . Was missing one screw for the buckle latch, no biggie. . . never throw out extra hardware from any install!! Overall happy with product

This is my 3rd BakFlip install over the past 9 years! I like how easy they are to install. I also like the low, clean appearance of the cover yet how secure they are from casual thieves etc. This new iteration feels lighter and better hinged. I like it!! My only complaint if you can call it that is that the 3 block bumpers have always resisted my attempts to peal the paper from the double sided tape that reveals the sticky side so you can install the bumps to the last panel that rest on the truck rear window. I can never get those to work properly.

I just installed my cover and it looks great. It was a very easy installation. The only part about the cover I dislike is once I put the cover on and looked around the whole thing the spots where it folds were a little torn up. Being brand new that shouldn't be like that.

Materials seem to be good quality. Bed cover is sturdy but does not adequately cover the bed. There are a few gaps that do not seal well. Will work well for keeping items safe from theft, but I would not recommend if you are looking for something that is watertight. It comes with drain tubes which can route a lot of water out of the bed, but a lot of water still ends up in the bed of the truck.

I tried to communicate this with Realtruck, but there was too much red tape to make it worthwhile. There is a MAJOR issue with the written instructions that come with the cover that I purchased. No where in the instructions does it say that the clamps that hold the rail onto the bed should snap into the rail. If you don't snap them into the rail then the whole thing does not work at all. It will not latch and close up. I had to search Youtube in order to find this.

It was very Disappointing or may be my expectations were to high!!!. . . never got the cover to latch naturally and properly unless you help it or force it ( is not the way it supposed to work ) the clips that holds the bed cover tight with the railing interfere with the hardware ( ended up both line up in the same spot ) plastic clips on the end of over railing sistem comes loose pretty easy ( not supposed to be like that ) installation were rate as easy to install ( turned into a headache ) got me working on it over 3 times. In Resume. Overall quality i think was poor ( I could expect that from an unbranded product from Amazon or so ) not from the a top saller product

I had a 2017 Ridgeline and loved the Bakflip. Purchased 2025 Ridgeline and a new Bakflip and could not get it mounted - rails are not as sturdy and I found others online with similar issues. Went back and mounted the 2017 Bakflip onto the 2025 Ridgeline and it was simple and easy. RealTruck really needs to look at the design of the rail systems.

Well let's see. It's been over a month since I placed my order. When I placed my order, the product was supposedly in stock and ready to ship. Still nothing. I am going to cancel my order and get the same bed cover from someone else. But since you asked for a review, here it is.

I took it to a professional install place for BakFlip. They say the parts for 2025 pro 4X was not great . They had to adjust finally got it to shut. But they told me today to reach out to you and say it not a normal installation. ( I try to reach customer service but it was a 30 plus min wait. Today 6/4/25

I originally had a cover bought off amazon and it fits perfectly. I wanted to have a stronger cover and tried this one. However, water seeps in when it rains and in carwashes. My original cover bought cheaper from amazon doesn't do that. I hope they created it a little 0. 5 longer. Waste of $$$$.