BAKFlip 448701 MX4 (GEN 3) Hard Folding Tonneau Cover Fits 2020-2026 Jeep Gladiator 5' Bed

I went from a ARE fiberglass lid to this. . . Which limits you extremely. . The MX4 cover looks really good. . . . Easy install. . locks with tailgate. . Was missing one screw for the buckle latch, no biggie. . . never throw out extra hardware from any install!! Overall happy with product

I really tried my best with help to make the side rail square with bed sides. The foam strip seems to put the rail at an angle. I loosened/tighted the rails to no avail. The cover does leak but not excessively but it leaks. Any advice would be appreciated. S.

This is my 3rd BakFlip install over the past 9 years! I like how easy they are to install. I also like the low, clean appearance of the cover yet how secure they are from casual thieves etc. This new iteration feels lighter and better hinged. I like it!! My only complaint if you can call it that is that the 3 block bumpers have always resisted my attempts to peal the paper from the double sided tape that reveals the sticky side so you can install the bumps to the last panel that rest on the truck rear window. I can never get those to work properly.

When I purchased my truck it had a Peragon Classic retractable cover. I grew tired of my equipment getting wet. While no coveris100% waterproof I was impressed after going through the car wash. Install . . only one glitch. . it wasn't clear that the front rail tab went in at slight angle and the snapped in. . No real issue with the install even as I did it alone. . great looks and great product. .

I just installed my cover and it looks great. It was a very easy installation. The only part about the cover I dislike is once I put the cover on and looked around the whole thing the spots where it folds were a little torn up. Being brand new that shouldn't be like that.

Installation was much more difficult for the Maverick than what is indicated in the Realtruck video. For $1200 it would have been helpful for an instruction sheet specifically for this model to be included. The tolerances for the Bakflip are so precise that any small imperfections in the truck bed are problematic. The drivers side latched perfectly but the passenger side would not latch for all three latches. Yes, the railing was installed correctly and identically on both sides. Determined that the truck bed was slightly leaning in on the passenger side. Had to correct by placing a flat washer as a shim under each latching mechanism. Also, the thick pads included to protect the cab are not thick enough for the Maverick. When the bed cover is flipped up it rests on the cab and the pads do not reach the cab. The rear window is recessed from the cab frame and the pads do not reach the window. The only place where the pads would actually work are on the very edge of the cover, and then it would not be able to close.

Materials seem to be good quality. Bed cover is sturdy but does not adequately cover the bed. There are a few gaps that do not seal well. Will work well for keeping items safe from theft, but I would not recommend if you are looking for something that is watertight. It comes with drain tubes which can route a lot of water out of the bed, but a lot of water still ends up in the bed of the truck.

I specifically order this because it stated “rapid ship” and indicated it would ship on the day I placed the order. I waited for 4 days and there was no shipping information. It took forever to get through to customer service who could not resolve the issue. I waited a couple more days and was finally told it would ship the next day. Then I had and issue with one of the rubber bumpers that came off and again called customer service who said they would refer it to the BakFlip team and they would reach out to me. That was last week and I have yet to hear back from anyone.

I tried to communicate this with Realtruck, but there was too much red tape to make it worthwhile. There is a MAJOR issue with the written instructions that come with the cover that I purchased. No where in the instructions does it say that the clamps that hold the rail onto the bed should snap into the rail. If you don't snap them into the rail then the whole thing does not work at all. It will not latch and close up. I had to search Youtube in order to find this.

I set a tire on top and drove around the building, which is about 200 yards and that's a big circular scratch on it. I didn't realize I was buying something with such a soft surface where I wouldn't have. Truck denied my request to return it even though they have the monopoly the industry. I'm not impressed.