Omix-Ada by RealTruck | 16737.44 | Brake Line Kit, Full | OE Reference: 531010 | Compatible with 1981-1986 Jeep CJ7

Fairly easy install. The videos help a lot. I had a slight issue with the rails leaning down slightly after being tightened. This kept the latches from catching when unrolled. After re-installing several times to see if I'd done something wrong, I just used a pair channel locks and bent the rails ever so slightly where the latches would make contact. Just enough to get it to latch without actually being able to see it. Worked great from there out.

Cover is good overall. The instructions could be clearer on the clamping the rails down section. Overall it looks good. However I had a bumper peice fall off already. The one that sits flush on top of the cover by the cab window when not in use. Hopefully it lasts a long time.

I just installed my cover and it looks great. It was a very easy installation. The only part about the cover I dislike is once I put the cover on and looked around the whole thing the spots where it folds were a little torn up. Being brand new that shouldn't be like that.

4 inch long rubber bumpers that the cover edge sits on while fully open, not affixed very well. They were low quality adhesive. Cleaned off and used 3M trim double sided tape to fix. Stuck well now. Was disappointed to to see latches were plastic. Overall, product will work.

The installation didn't go as well as I had expected. I followed the provided instructions and the latches on the panels didn't line up correctly and wouldn't latch without me lifting the rail up. Because of the fitmet issue, it took me approximately two hours to install. The following day, I did research on the internet and found a reddit post outlining this as others experienced the same issue. Someone posted a link to a good video that showed installation with the brackets being snapped onto the rail. I removed my cover and rails and did another install snapping the brackets into the rail. The brackets are supposed to connect on the top notch but my middle brackets won't connect on the top notch so I had to connect on the bottom notch. The panels now latch as they should. I noticed that I can see some daylight in the corners of the cover by the cab, so I'll jave to put on more weather stripping in those spots. For the price, I expected better instructions.

I specifically order this because it stated “rapid ship” and indicated it would ship on the day I placed the order. I waited for 4 days and there was no shipping information. It took forever to get through to customer service who could not resolve the issue. I waited a couple more days and was finally told it would ship the next day. Then I had and issue with one of the rubber bumpers that came off and again called customer service who said they would refer it to the BakFlip team and they would reach out to me. That was last week and I have yet to hear back from anyone.

Materials seem to be good quality. Bed cover is sturdy but does not adequately cover the bed. There are a few gaps that do not seal well. Will work well for keeping items safe from theft, but I would not recommend if you are looking for something that is watertight. It comes with drain tubes which can route a lot of water out of the bed, but a lot of water still ends up in the bed of the truck.

Installation was much more difficult for the Maverick than what is indicated in the Realtruck video. For $1200 it would have been helpful for an instruction sheet specifically for this model to be included. The tolerances for the Bakflip are so precise that any small imperfections in the truck bed are problematic. The drivers side latched perfectly but the passenger side would not latch for all three latches. Yes, the railing was installed correctly and identically on both sides. Determined that the truck bed was slightly leaning in on the passenger side. Had to correct by placing a flat washer as a shim under each latching mechanism. Also, the thick pads included to protect the cab are not thick enough for the Maverick. When the bed cover is flipped up it rests on the cab and the pads do not reach the cab. The rear window is recessed from the cab frame and the pads do not reach the window. The only place where the pads would actually work are on the very edge of the cover, and then it would not be able to close.

It was very Disappointing or may be my expectations were to high!!!. . . never got the cover to latch naturally and properly unless you help it or force it ( is not the way it supposed to work ) the clips that holds the bed cover tight with the railing interfere with the hardware ( ended up both line up in the same spot ) plastic clips on the end of over railing sistem comes loose pretty easy ( not supposed to be like that ) installation were rate as easy to install ( turned into a headache ) got me working on it over 3 times. In Resume. Overall quality i think was poor ( I could expect that from an unbranded product from Amazon or so ) not from the a top saller product

I ordered my part almost a month ago. I have not received it. I tried numerous times to get an update with no success. I am heading out for an extended trip and I needed the topper. Now I have to consider not having the part I needed for my trip. To add insult to injury I am being asked how I like the part I never receive. Kind of silly. Not a great first experience of a company that is “apparently” highly regarded. I am not a person of high expectations I just would like to know if I will get my part in time to install it before my trip. They took my payment. Will they be just as eager to return it? We shall see in 2 days when I will demand a refund.