J-B Weld ClearWeld Syringe Epoxy Adhesive Clear 25 ml

I used this epoxy to mend a porcelain decorative item. It did everything the ad said. Dried quickly, is holding together and the item was tricky to mend. No seam exposed. ( Follow MFD) My first time working w an epoxy. Very pleased and highly recommend.

For many years now, I purchased this brand and product over and over again. Epoxy is on such a higher level than regular glue. Because it comes in 2 parts that must be evenly mixed together, you get a bond and hardness that other glue can't deliver. I use it around the house for many things. They also have one especially for metal that works great. Epoxy is more work because you have to mix equal parts thoroughly, it's messier and takes a little more effort than regular glue, but the results are worth it. I keep a supply of little paper plates and I use a wooden toothpick to mix. Or just use a piece of cardboard . It sets up quickly so don't dilly dally. You get a 5 minute window. When you are done, squeeze the dispenser almost to the top so there is no air, clean any excess off the lid and dispenser with a napkin and replace the top. Store it upright on its stand alone feet. Your next use will be like opening a new tube and you will get the best results. A tube lasts me 2 or 3 years for general use.

it dries clear in a reasonable amount of time and is fully cured in 24hrs or so. depending on thickness of application. a little really goes a long way. be careful to get air bubbles out before dispensing so the product comes out in equal quantity. I have used my epoxy 6 times and the lid still comes off without trouble.

I used this on my commercial kitchen plastic wallboards. It cured fast so I did not have to hold the item to the wall too long. Very, very strong bond! I've used J-B Weld products for years and highly recommend this product.

Had a corner of a glass frame cracked. Used the weld to repair it. Worked so well you barely see it. Once it set it was as secure as if it wasn't broken.

It dried nice and fast. I wasn't sure if I mixed well enough because this stuff is clear, but it must have been enough because it set up well and fast. Very convenient because it meters out the two components equally without guessing.

Inconvenient and high waste of product due to mixing. However the bond strength across multiple mediums is far superior to any non mixing direct application adhesive product.

Plastic parts (wood-pattern plastic accents) inside my car popped up, I think the old glue gave out after 15yrs, so I bought this epoxy glue to fix the problem. The application was easy and I applied pressure with my hands to hold the parts in-place for drying -- I later taped things on top to keep the pressure for several days before removing everything to check results. The result was the plastic part still popped...didn't work. Maybe it works on other materials...but it didn't for this case of plastic-on-plastic.

it does better with plastic items than metal, takes too long to mix if you need a quick, strong, secure hold...about 3 to 5 min is the mix time/set time, then it has to cure...you don't just squeeze it out, mix it and it holds, it takes a bit of patience. if you want something like that don't get this. after it dries it does work very well, I changed my mind and did not use on my intended project,which had a get deal of metal. I just used on other tiny repairs, mostly plastic, it did alright. I will go back to buying the putty and trying that again. it worked better for me. I suppose this has it use and place. good luck

After using several JB weld products over the years, I'm not sure how this made it out of testing. I tried this a few times, let it cure for days and it winds up being tacky and not strong. I had high hopes for this being that it's great for white plastic and the Grey JB weld always leaves residual that it's been glued. The Grey epoxy works terrific. This stuff is a headache and a waste of time. I've tried this on about 10 different items and each time I had to clean it off and use the Grey epoxy instead. Save your time and money and skip this.